How To Remove A Samsung Fridge Evaporator Cover

If you have a Samsung fridge, you may need to remove the evaporator cover at some point for cleaning, maintenance, or replacement. The evaporator cover is the plastic panel that covers the evaporator coil and fan in the back of your fridge. It may also have a temperature sensor attached to it. Removing the evaporator cover on a Samsung fridge is not very difficult, but it does require some care and attention. In this post, we’ll show you how to remove Samsung fridge evaporator cover in a few simple steps.

To remove the Samsung fridge evaporator cover, you need to open the fridge door, remove the shelves and drawers, unscrew the screws holding the cover, pry off the cover with a spudger or a putty knife, disconnect the connector and the sensor, and slide out the cover. To reinsert it, you need to reverse the process and make sure the cover is securely in place.

Why You May Need to Remove Samsung Fridge Evaporator Cover

There are several reasons why you may need to remove the evaporator cover on your Samsung fridge. Some of them are:

• To clean the evaporator coil and fan from dust, dirt, or ice buildup that may affect their performance or cause noise.
• To access the drain hole or the defrost heater behind the cover that may be clogged or malfunctioning.
• To replace a broken or damaged evaporator cover, fan, or sensor.
• To troubleshoot a problem with your fridge that may be caused by a faulty evaporator coil, fan, or sensor.

Whatever your reason is, removing the evaporator cover on your Samsung fridge is not a complicated task, but it does require some caution and patience. You don’t want to damage your fridge or hurt yourself in the process.

How to Remove Samsung Fridge Evaporator Cover

The exact method of removing the evaporator cover on your Samsung fridge may vary depending on the model and type of your fridge. However, here are some general steps that apply to most Samsung fridges:

• Open the fridge door and remove any items on the shelves and drawers. You may also want to remove any items on the door bins to avoid them falling down when you remove the cover.
• Remove the shelves and drawers from your fridge by pulling them out gently. You may need to lift them up slightly to release them from their slots.
• Locate the screws that hold the evaporator cover in place. They are usually located at the top and bottom of the cover. Use a Phillips head screwdriver to unscrew them. Keep them in a safe place for later use.
• Use a spudger or a putty knife to pry off the evaporator cover from its clips. Start from the bottom and work your way up. Be careful not to damage the plastic or metal beneath it.
• Disconnect the connector and the sensor that are attached to the evaporator cover. The connector is usually located at the top right corner of the cover. The sensor is usually located at the bottom left corner of the cover. You may need to cut a cable tie that holds them in place.
• Slide out the evaporator cover from your fridge. Be careful not to drop it or hit anything with it.

How to Reinsert Samsung Fridge Evaporator Cover

To reinsert the evaporator cover on your Samsung fridge, you need to follow these steps:

• Slide in the evaporator cover into your fridge. Make sure it aligns properly with its slots and clips.
• Reconnect the connector and the sensor that are attached to the evaporator cover. The connector goes into its socket at the top right corner of the cover. The sensor goes into its slot at the bottom left corner of the cover. You may need to use a new cable tie to secure them in place.
• Use a spudger or a putty knife to snap in the evaporator cover into its clips. Start from the top and work your way down. Make sure it is firmly attached and flush with the back wall of your fridge.
• Screw in the screws that hold the evaporator cover in place. They go into their holes at the top and bottom of the cover. Use a Phillips head screwdriver to tighten them.
• Put back any items on the shelves and drawers into your fridge. You may also want to put back any items on the door bins.

FAQs About Removing Samsung Fridge Evaporator Cover

Here are some common questions and answers about removing Samsung fridge evaporator cover:

Q: How do I clean my Samsung fridge evaporator coil and fan?

A: To clean your Samsung fridge evaporator coil and fan, you can use a soft brush or a vacuum cleaner with a brush attachment to remove any dust, dirt, or ice buildup from them. You can also use warm water and mild soap or detergent to wipe them with a soft cloth or sponge. Rinse them well and dry them with a clean towel or let them air dry before putting back the evaporator cover.

Q: How do I unclog my Samsung fridge drain hole or defrost heater?

A: To unclog your Samsung fridge drain hole or defrost heater, you can use a turkey baster or a syringe to inject hot water into them. You can also use a thin wire or a pipe cleaner to poke through them and dislodge any debris or ice. You may need to repeat this process several times until the water drains freely.

Q: How do I replace my Samsung fridge evaporator fan or sensor?

A: To replace your Samsung fridge evaporator fan or sensor, you can order new ones from Samsung’s website or authorized dealers. Make sure you have your model number handy when ordering. You can also check out our post on how to replace Samsung fridge evaporator fan for more information.

Conclusion

Removing the evaporator cover on your Samsung fridge is a simple and quick process that can help you access and maintain the evaporator coil, fan, and sensor in the back of your fridge. To remove it, you need to open the fridge door, remove the shelves and drawers, unscrew the screws holding the cover, pry off the cover with a spudger or a putty knife, disconnect the connector and the sensor, and slide out the cover. To reinsert it, you need to reverse the process and make sure the cover is securely in place.