To reset the water filter on your GE French door refrigerator, you need to replace the old filter with a new one and then reset the filter indicator on the screen or the control panel. You can use a screwdriver or pliers to remove the old filter and insert the new one. You can also use a level to check if the refrigerator is tilted or not. To reset the filter indicator, you need to press and hold the Ice & Water pad or the Reset button for three seconds until the light turns green or the message disappears.
How To Reset Water Filter On GE French Door Refrigerator In Four Steps
Before you start resetting the water filter on your GE French door refrigerator, you will need some tools and materials, such as:
- A new water filter
- A screwdriver or pliers
- A level
- An owner’s manual
You will also need an extra person to help you move the refrigerator if needed.
Here are the four steps to reset the water filter on your GE French door refrigerator:
- Step 1: Remove the old water filter. Open the fridge doors and locate the compartment labeled “Water Filter”. Press the tabs to open the cover, then swivel the filter out 45 degrees, twist it, and pull it straight out. Dispose of the old filter properly.
- Step 2: Install the new water filter. Pour some water into the new filter by bringing it up to the sink faucet. This will help to remove any air bubbles or carbon dust from the filter. Insert the new filter into the filter cartridge opening on the refrigerator. Align it with the grooves and push it in until it clicks into place. Swivel it back into position and close the cover.
- Step 3: Check if the refrigerator is level. Place a level on top of the refrigerator (not on the door) near the front and measure from front to back and side to side. If the level is not flat, you need to adjust the feet or rollers at the bottom of your refrigerator until it is. To raise or lower your refrigerator, turn them clockwise or counterclockwise with a screwdriver or pliers. Try to get your refrigerator level from left to right and slightly tilted to the back for proper door closure.
- Step 4: Reset the filter indicator. Depending on your model of GE French door refrigerator, you may have a touch screen or touch pads on your control panel. To reset the filter indicator, follow these steps:
- Touch Screen Models: A filter status message will appear on the screen when the water filter needs to be replaced. The filter status will automatically update when a new RFID (radio frequency identification) filter is installed. If you are using a non-RFID filter, you can manually reset the filter status by pressing Settings > Water Filter > Reset Filter Status > Yes.
- Non-Touch Screen Models: A Water Filter indicator light will illuminate on the control panel when the water filter needs to be replaced. It will stop illuminating when a new RFID filter is installed. If you are using a non-RFID filter, you can manually reset the indicator light by pressing and holding the Ice & Water pad for three seconds until it turns green. Alternatively, locate the Reset button near the water filter compartment and press and hold it for three seconds to turn off the light.
When To Call A Professional
If you have tried all of these steps and your water filter indicator still does not reset, you may have a more complex problem that requires professional help. Some of these problems include:
- A faulty RFID chip: The RFID chip is embedded in some GE water filters and communicates with your refrigerator to detect leaks and monitor the filter status. If your RFID chip is defective or damaged, it may not be able to send or receive signals from your refrigerator and cause your indicator light or message to stay on. You may need to replace your RFID chip or use a non-RFID filter instead.
- A faulty control board: The control board is responsible for controlling various functions of your refrigerator, including displaying messages and lights on your screen or panel. If your control board is malfunctioning or corrupted, it may not be able to recognize or reset your water filter indicator properly. You may need to replace your control board or update its software.
Conclusion
A water filter on your GE French door refrigerator helps to improve the quality and taste of your drinking water. To reset the water filter on your GE French door refrigerator, you need to replace the old filter with a new one and then reset the filter indicator on the screen or the control panel. You can use a screwdriver or pliers to remove the old filter and insert the new one. You can also use a level to check if the refrigerator is level or not. To reset the filter indicator, you need to press and hold the Ice & Water pad or the Reset button for three seconds until the light turns green or the message disappears.
If you have tried all of these steps and your water filter indicator still does not reset, you may have a more serious problem that requires professional help. Some of these problems include a faulty RFID chip or a faulty control board. You should call a professional technician to diagnose and repair these problems.
