Replacing GE Freezer Seal: A Step-by-Step Guide for Beginners

If you have a GE freezer, you may need to replace the freezer seal at some point. The freezer seal, also known as the door gasket, is the rubber strip that runs around the edge of the freezer door. It creates an airtight seal that prevents cold air from escaping and warm air from entering the freezer. This helps to keep your food frozen and prevent frost buildup.

However, over time, the freezer seal can wear out, crack, or lose its shape. This can cause your freezer to run inefficiently, use more energy, and spoil your food faster. You may notice signs of a bad freezer seal, such as:

• The freezer door is hard to open or close
• The freezer door pops open by itself
• There is ice or frost on the freezer walls or door
• There is condensation or water droplets on the freezer seal
• The freezer seal is torn, loose, or sagging

If you notice any of these signs, you should replace the freezer seal as soon as possible. Replacing the freezer seal is not a difficult task, and you can do it yourself with some basic tools and a new seal.

To replace a GE freezer seal, you need to remove the old seal, clean the door groove, install the new seal, and check for a proper fit. The exact steps depend on the type of seal you have and the model of your freezer.

In this post, we will show you how to replace a GE freezer seal in simple steps. We will also explain how to find the model number of your freezer, where to order a new seal, and how to care for your new seal.

How to Find the Model Number of Your Freezer

To order a new freezer seal, you need to know the model number of your freezer. This will help you find the right part that matches your freezer.

The model number is usually located on a label inside your freezer, on the left wall near the top. It may also be on the back or bottom of your freezer. The model number usually starts with a letter followed by numbers and letters.

You can also use the GE website to find your model number by entering your product type and features.

How to Order a New Freezer Seal

Once you have your model number, you can order a new freezer seal from various sources. You can use the GE website to search for parts by model number or part number. You can also use other online retailers or local appliance stores that sell GE parts.

The part number for the freezer seal may vary depending on the size and shape of your freezer door. For example, the part number for a white freezer door gasket for model FCM7SKWW is WR24X23252. You can find the part number on the old seal or on the packaging of the new seal.

How to Replace a GE Freezer Seal

Depending on the type of seal you have, follow these steps to replace a GE freezer seal:

• For seals that can be pulled away from the door, start at one corner and gently pull the old seal out of the groove that goes around the door. Work your way around until you remove the entire seal. Discard the old seal.
• For seals that are sealed to the door, use a utility knife to carefully cut along the edge of the old seal. Cut along the top first, then the sides and finally the bottom edge before discarding the old seal.
• Use a damp cloth or sponge to clean any dirt or residue from the door groove. Make sure it is dry before installing the new seal.
• Position the new seal around the inner door liner. Start at one top corner and press the seal firmly into place along the top until you reach the other corner. Then repeat this process at the sides and bottom of the door until you fit the entire seal.
• Check that there are no gaps or wrinkles in the new seal and that it fits snugly around the door. If needed, use a hair dryer on low heat to soften any stiff areas and smooth them out with your fingers.
• Lubricate the new seal with some petroleum jelly or silicone spray to prevent it from sticking or cracking.

If you need more guidance, you can watch these videos for more details:

• GE Refrigerator Repair – How to Replace the Freezer Door Gasket (GE # WR24X10228)
• How To: GE Freezer Door Gasket WR24X23252

FAQs

Q: How do I replace a GE freezer seal?

A: To replace a GE freezer seal, you need to remove the old seal, clean the door groove, install the new seal, and check for a proper fit. The exact steps depend on the type of seal you have and the model of your freezer.

Q: How do I find the model number of my freezer?

A: The model number is usually located on a label inside your freezer, on the left wall near the top. It may also be on the back or bottom of your freezer. The model number usually starts with a letter followed by numbers and letters. You can also use the GE website to find your model number by entering your product type and features.

Q: How do I order a new freezer seal?

A: Once you have your model number, you can order a new freezer seal from various sources. You can use the GE website to search for parts by model number or part number. You can also use other online retailers or local appliance stores that sell GE parts.

Conclusion

Replacing a GE freezer seal is a simple and effective way to improve the performance and efficiency of your freezer. Whether you have a seal that can be pulled away or a seal that is sealed to the door, you can remove and install it in a few steps. However, make sure you order the right seal for your freezer model and follow the instructions carefully.