If you have a Kenmore bottom freezer refrigerator, you may need to change the water filter every 6 months or sooner, depending on your water usage and quality. The water filter is responsible for removing contaminants and impurities from your water and ice dispenser, ensuring that you have fresh and clean water at all times.
However, over time, the filter can get clogged or saturated with dirt and bacteria, which can affect its performance and efficiency. To prevent this, you need to replace the filter with a new one that is compatible with your refrigerator model. In this post, we’ll show you how to change the water filter on your Kenmore bottom freezer refrigerator in a few simple steps.
To change the water filter on your Kenmore bottom freezer refrigerator, you’ll need to locate the filter compartment on the front panel of the refrigerator, near the floor. Then, you’ll need to press the release button on the compartment and pull out the old filter.
Next, you’ll need to remove the cap from the old filter and attach it to the new filter. Finally, you’ll need to insert the new filter into the compartment and push it until it clicks into place.
How to locate the water filter compartment on your Kenmore bottom freezer refrigerator
The location of the water filter compartment on your Kenmore bottom freezer refrigerator depends on the model and features of your appliance. You can refer to your owner’s manual or installation instructions for specific details. Here are some general guidelines:
- For most models, the water filter compartment is located on the front panel of the refrigerator, near the floor. It looks like a small rectangular door with a button or tab on it.
- For some models (like the Kenmore Elite 795 series), the water filter compartment is located inside the refrigerator, in one of the top two corners. It looks like a small cylindrical housing with a button or tab on it.
How to change the water filter on your Kenmore bottom freezer refrigerator
To change the water filter on your Kenmore bottom freezer refrigerator, you’ll need the following tools:
- A new water filter that matches your model number
- A towel or cloth
You can order a replacement water filter from Kenmore or other online retailers. Make sure you have your model number handy when ordering, as different models may have different filters.
Here are the steps to follow:
- Unplug your refrigerator from the power source and turn off the water supply valve.
- Locate the water filter compartment on your refrigerator, as described above.
- Press the release button or tab on the compartment and pull out the old filter. You may hear some water dripping or spilling out of the compartment. Use a towel or cloth to catch any excess water.
- Remove the cap from the end of the old filter by twisting it counterclockwise or pulling it off. Set it aside. Discard the old filter.
- Take out the new filter from its packaging and remove any protective covers or seals from it.
- Attach the cap to the end of the new filter by twisting it clockwise or pushing it on. Make sure it’s secure and aligned with the grooves on the filter.
- Insert the new filter into the compartment and push it until it clicks into place. You may hear some air bubbles escaping from the filter as it fills with water.
- Close the compartment door and make sure it’s locked securely.
- Turn on the water supply valve and plug in your refrigerator.
- Flush out any air or debris from the new filter by dispensing about 3 gallons (11 liters) of water from your dispenser. You may notice some sputtering or cloudy water at first, but this is normal and will clear up after a few minutes.
- Press and hold the “Filter Reset” button near your dispenser for 3 seconds to reset your filter indicator light.
What to avoid when changing the water filter on your Kenmore bottom freezer refrigerator
When changing the water filter on your Kenmore bottom freezer refrigerator, there are some things you should avoid doing, such as:
- Don’t use a water filter that is not compatible with your model number. This can cause leakage, damage, or poor performance of your appliance.
- Don’t reuse or refill an old water filter. This can compromise its quality and effectiveness and introduce bacteria or contaminants into your water system.
- Don’t run hot water through your dispenser. This can damage your dispenser mechanism and cause cracking or warping of your plastic parts.
- Don’t forget to flush out your new filter before using it. This can prevent any air or debris from affecting your water quality and taste.
FAQs about Kenmore bottom freezer refrigerator water filters
Here are some of the most common questions that people have about Kenmore bottom freezer refrigerator water filters:
- How do I know if my Kenmore bottom freezer refrigerator water filter needs to be changed? Some signs that your Kenmore bottom freezer refrigerator water filter needs to be changed are:
- The filter indicator light on your dispenser turns red or flashes
- The water or ice from your dispenser tastes or smells bad
- The water or ice from your dispenser is cloudy or discolored
- The water or ice from your dispenser has a low flow rate or pressure
- The water or ice from your dispenser contains particles or sediment
- How often should I change my Kenmore bottom freezer refrigerator water filter? The frequency of changing your Kenmore bottom freezer refrigerator water filter depends on your water usage and quality. Generally, you should change it every 6 months or sooner, depending on the following factors:
- The amount of water or ice you dispense
- The hardness or softness of your water
- The presence of contaminants or impurities in your water
- The condition and age of your filter
- How much does a Kenmore bottom freezer refrigerator water filter cost? The cost of a Kenmore bottom freezer refrigerator water filter depends on the model and features of your appliance. Generally, they range from $15 to $50, which is reasonable compared to other types of filters.
Conclusion
A Kenmore bottom freezer refrigerator water filter is an essential part of your appliance that ensures that you have fresh and clean water and ice at all times. However, over time, the filter can get clogged or saturated with dirt and bacteria, which can affect its performance and efficiency. To prevent this, you need to replace the filter with a new one that is compatible with your refrigerator model. To do this, you need to locate the filter compartment on the front panel of the refrigerator, near the floor. Then, you need to press the release button on the compartment and pull out the old filter. Next, you need to remove the cap from the old filter and attach it to the new filter. Finally, you need to insert the new filter into the compartment and push it until it clicks into place. When changing the water filter, you should avoid using a filter that is not compatible with your model number, reusing or refilling an old filter, running hot water through your dispenser, or forgetting to flush out your new filter before using it. By following these tips and tricks, you can change the water filter on your Kenmore bottom freezer refrigerator without any hassle.
