If you have a Whirlpool freezer, you may need to replace the thermostat at some point. The thermostat is the part that regulates the temperature inside the freezer and controls the defrost cycle. If the thermostat is faulty, it can cause problems such as:
- The freezer not cooling properly or freezing too much
- The freezer not defrosting or defrosting too often
- The freezer running constantly or not running at all
- The freezer making loud noises or leaking water
To fix these issues, you can replace the thermostat with a new one. You can also calibrate the thermostat to make sure it’s set to the right temperature. In this post, we’ll show you how to replace the thermostat in a Whirlpool freezer and how to calibrate it.
To replace the thermostat in a Whirlpool freezer, you’ll need to unplug the freezer, remove the back panel, disconnect the wires, remove the old thermostat, install the new thermostat, reconnect the wires, and replace the back panel.
To calibrate the thermostat, you’ll need to adjust the temperature setting according to your preference and wait for 24 hours to check the results.
How to replace the thermostat in a Whirlpool freezer
To replace the thermostat in a Whirlpool freezer, you’ll need the following tools:
- A new thermostat that matches your model number
- A Phillips screwdriver
- A flathead screwdriver
- Needle-nose pliers
You can order a replacement thermostat from Whirlpool or other online retailers. Make sure you have your model number handy when ordering, as different models may have different thermostats.
Here are the steps to follow:
- Unplug your freezer from the power source and empty any items from it.
- Locate the back panel of your freezer and remove the screws that hold it in place. Use a Phillips screwdriver to do this and set them aside. Be careful not to lose them, as you’ll need them later.
- Pull out the back panel and set it aside. You should see the thermostat attached to a metal bracket near the evaporator coils. It looks like a small metal box with two wires coming out of it.
- Disconnect the wires from the thermostat by pulling them off with needle-nose pliers. Be careful not to damage them, as you’ll need them later.
- Remove the old thermostat from the bracket by unscrewing it with a flathead screwdriver or by snapping it off with your fingers. Discard it.
- Align the new thermostat with the bracket and secure it with a screw or by snapping it into place. Make sure it’s firmly attached and not loose.
- Reconnect the wires to the new thermostat by pushing them onto their terminals with needle-nose pliers. Make sure they’re connected correctly and not loose.
- Replace the back panel and secure it with the screws that you removed earlier. Use a Phillips screwdriver to do this and tighten them.
- Plug in your freezer and turn it on. Check if it’s working properly.
How to calibrate the thermostat in a Whirlpool freezer
To calibrate the thermostat in a Whirlpool freezer, you’ll need to adjust the temperature setting according to your preference and wait for 24 hours to check the results. Here are some general guidelines:
- Locate the temperature control on your freezer, which may be a digital button, a dial, or a slider. You can refer to your owner’s manual or installation instructions for specific details.
- Adjust the temperature setting according to your preference. To make your freezer colder, increase the setting. To make it warmer, lower the setting. The setting may be a number from 1 to 10, or a range from “cold” to “coldest”.
- Wait for 24 hours for the temperature to stabilize before checking it again. You can use a thermometer to measure the temperature inside your freezer.
- If necessary, adjust the setting again until you reach your desired temperature.
What to avoid when replacing or calibrating the thermostat in your Whirlpool freezer
When replacing or calibrating the thermostat in your Whirlpool freezer, there are some things you should avoid doing, such as:
- Don’t replace or calibrate the thermostat without unplugging your freezer first. This can prevent electric shock or damage to your appliance.
- Don’t use a thermostat that is not compatible with your model number. This can cause malfunction or damage to your appliance.
- Don’t set the temperature too high or too low. The recommended temperature for your freezer is between 0°F and 5°F (-18°C and -15°C). Setting it too high can cause food spoilage and bacterial growth. Setting it too low can cause food freezing and energy waste.
- Don’t overload or underload your freezer. Keep your freezer at least three-quarters full. This can help maintain a consistent temperature and reduce air leakage when opening and closing the door.
FAQs about Whirlpool freezer thermostat
Here are some of the most common questions that people have about Whirlpool freezer thermostat:
- How do I know if my Whirlpool freezer thermostat is faulty? Some signs that your Whirlpool freezer thermostat is faulty are:
- The freezer not cooling properly or freezing too much
- The freezer not defrosting or defrosting too often
- The freezer running constantly or not running at all
- The freezer making loud noises or leaking water
- How much does a Whirlpool freezer thermostat cost? The cost of a Whirlpool freezer thermostat depends on the model and features of your appliance. Generally, they range from $10 to $50, which is reasonable compared to other types of thermostats.
- How long does a Whirlpool freezer thermostat last? The lifespan of a Whirlpool freezer thermostat depends on how well you maintain it and how often you use it. On average, a thermostat can last for about 10 years, but some models can last longer or shorter depending on the quality and usage.
Conclusion
A Whirlpool freezer thermostat is an important part of your appliance that regulates the temperature inside the freezer and controls the defrost cycle. If the thermostat is faulty, it can cause problems such as the freezer not cooling properly or freezing too much, the freezer not defrosting or defrosting too often, the freezer running constantly or not running at all, the freezer making loud noises or leaking water. To fix these issues, you can replace the thermostat with a new one. You can also calibrate the thermostat to make sure it’s set to the right temperature. To do this, you need to unplug the freezer, remove the back panel, disconnect the wires, remove the old thermostat, install the new thermostat, reconnect the wires, and replace the back panel. To calibrate the thermostat, you need to adjust the temperature setting according to your preference and wait for 24 hours to check the results. By following these tips and tricks, you can replace and calibrate the thermostat in your Whirlpool freezer without any hassle.
